RIPの設定

スポンサーリンク

目的

異なるネットワークに所属している2台のPCをお互いに通信させます。
ルーティングプロトコルはRIPv1を使用します。

RIPの設定方法を学びます。

接続構成

設定

R1の設定

R1(config)#int f0/0
R1(config-if)#ip add 192.168.1.1 255.255.255.0
R1(config-if)#no shut

R1(config-if)#int s0/0
R1(config-if)#ip add 192.168.2.1 255.255.255.0
R1(config-if)#no shut

R1(config)#router rip
R1(config-router)#network 192.168.1.0
R1(config-router)#network 192.168.2.0
RIPの設定

R2の設定

R2(config-if)#int s0/0
R2(config-if)#ip add 192.168.2.2 255.255.255.0
R2(config-if)#no shut

R2(config)#int f0/0
R2(config-if)#ip add 192.168.3.1 255.255.255.0
R2(config-if)#no shut

R2(config)#router rip
R2(config-router)#network 192.168.2.0
R2(config-router)#network 192.168.3.0
RIPの設定

PC-1の設定

PC-1> ip 192.168.1.100/24 192.168.1.1
Checking for duplicate address...
PC1 : 192.168.1.100 255.255.255.0 gateway 192.168.1.1

PC-1> save
Saving startup configuration to startup.vpc
. done

PC-2の設定

PC-2> ip 192.168.3.100/24 192.168.3.1
Checking for duplicate address...
PC2 : 192.168.3.100 255.255.255.0 gateway 192.168.3.1

PC-2> save
Saving startup configuration to startup.vpc
. done

設定確認

ルーティングプロトコルの確認

R1#sh ip protocols
Routing Protocol is "rip"・・・①
  Sending updates every 30 seconds, next due in 1 seconds
  Invalid after 180 seconds, hold down 180, flushed after 240
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Redistributing: rip
  Default version control: send version 1, receive any version
    Interface             Send  Recv  Triggered RIP  Key-chain
    FastEthernet0/0       1     1 2
    Serial0/0             1     1 2
  Automatic network summarization is in effect
  Maximum path: 4
  Routing for Networks:
    192.168.1.0・・・②
    192.168.2.0
  Routing Information Sources:
    Gateway         Distance      Last Update
    192.168.2.2          120      00:00:27
  Distance: (default is 120)

①有効化されているルーティングプロトコルは 「RIP」
②RIPを有効にしたインターフェースは 「192.168.1.0」と「192.168.2.0」

ルーティングテーブルの確認

R1#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.1.0/24 is directly connected, FastEthernet0/0
C    192.168.2.0/24 is directly connected, Serial0/0
R    192.168.3.0/24 [120/1] via 192.168.2.2, 00:00:08, Serial0/0

最後の行に注目しましょう。それぞれの項目の意味を説明します。

S
ルートの情報源、RIPのこと。

192.168.3.0/24
リモートネットワーク。

[120/1]
120は、アドミニストレーティブディスタンス。
1は、メトリック(ホップ)

via 192.168.2.2
ネクストホップ。

00:00:08
更新後の時間。
RIPはデフォルトで30秒間隔でルーティングアップデートを送信するので、この例ではアップデート後、30秒経過したことを表す。

Serial0/0
到達可能インターフェース(自分自身のインターフェースを指す)

まとめます。
ルーティングプロトコルは、RIPを使っていて、
192.168.3.0/24のネットワークは、Serial0のインターフェースからルータを1つ越えた先にある。

動作確認

Pingの疎通テスト

PC-1からPC-2
PC-1> ping 192.168.3.100
192.168.3.100 icmp_seq=1 timeout
84 bytes from 192.168.3.100 icmp_seq=2 ttl=62 time=78.283 ms
84 bytes from 192.168.3.100 icmp_seq=3 ttl=62 time=78.137 ms
84 bytes from 192.168.3.100 icmp_seq=4 ttl=62 time=78.335 ms
84 bytes from 192.168.3.100 icmp_seq=5 ttl=62 time=78.168 ms 
PC-2からPC-1
PC-2> ping 192.168.1.100
84 bytes from 192.168.1.100 icmp_seq=1 ttl=62 time=78.186 ms
84 bytes from 192.168.1.100 icmp_seq=2 ttl=62 time=78.129 ms
84 bytes from 192.168.1.100 icmp_seq=3 ttl=62 time=77.909 ms
84 bytes from 192.168.1.100 icmp_seq=4 ttl=62 time=78.097 ms
84 bytes from 192.168.1.100 icmp_seq=5 ttl=62 time=78.166 ms

異なるセグメントのPCがお互いに通信できることが確認できます。

タイトルとURLをコピーしました